Configuring Timer DI operating mode

時間：2021-07-28作者：上海騰希電氣技術有限公司瀏覽：111

Configuring Timer DI operating mode



Timer DI

Timer DI operating mode allows you to acquire the switching time of up to two edges per application cycle (for example OB 91, OB 6x), for example for use as a measuring output.

Select the Timer DI operating mode for the required channel.


圖片: Operating mode: Timer DI

Inversion

You can invert the 24 V ** to adjust it to your process. By default, the ** is not inverted.

Input delay

To suppress faults, you can set an input delay of 1 μs or 125 μs for the input filter of the digital inputs. Changes to the ** are only detected if they are constantly pending for longer than the set input delay time.

To allow **s pending very briefly to be detected with timer DI (for example level of 100 μs), set an input delay of 1 μs.

Assigning the measuring input technology object

The measuring input technology object must always be assigned to another technology object whose position is evaluated by the measuring input.

You can assign the measuring input technology object to the following technology objects:

Synchronous axis

Positioning axis

External encoder

You can assign the measuring input technology object precisely one axis or one external encoder.

You can assign multiple measuring input technology objects to one axis or one external encoder.

Configuring the measuring input technology object

Select the configuration of the measuring input in the Technology objects folder in the project tree.

Configure the basic properties of the technology object in the Basic parameters configuration window.


圖片: Basic parameters

Name

Define the name of the measuring input in this field. The technology object is listed under this name in the project tree. The tags of the measuring input can be used in the user program under this name.

Assigned axis or external encoder

STEP 7 displays the axis or external encoder assigned to the measuring input. You can use the link to directly access the basic parameters of the higher-level technology object.

Unit of measurement

The unit of measure shown for the position of the measuring input corresponds to the unit of measure of the higher-level technology object.

Hardware interface

In the Hardware interface configuration window, assign the a measuring input type Timer DI and the selected channel to the technology object.


圖片: Hardware interface

Measuring input type: Measuring using Timer DI

Select a measurement input for a measurement using a Timer DI. The selection box displays all channels that have been configured correctly.

提示 Extending the configuration limits A maximum of eight timer DI can be configured at the X142 interface. If the timer DI at X142 are not sufficient for your needs, you can configure a further eight measuring inputs at interface X122/X132. You can also extend the configuration limits using time-based I/O modules: ET 200SP distributed I/O system: TM Timer DIDQ 10x24V ET 200MP distributed I/O system: TM Timer DIDQ 16x24V You can find more information on these systems in .




提示 Unsupported instructions for X142 The function blocks for the use of time-based IO (TIO instructions) are not supported by the X142 interface. Recommendation: Use the measuring input technology object for timer DI.




Adjustment for measuring range activation time

To adjust the activation time defined in the system, enter an additional activation time in the Extended parameters configuration window.

Lost Edge Counter (LEC)

Timer DI support Lost Edge Counter. If more than two edges to be detected occur within one position control cycle, a measured value cannot be evaluated for the other edges to be detected. The LEC records the number of edges lost.

Which lost edges are recorded in the LEC depends on the mode set in the Motion Control instruction. For example, if you only want to measure rising edges, the LEC only records the rising edges not measured. The LEC can count and display a maximum of seven lost edges. The number of lost edges is displayed in the function block and in the technology data block.

Further information

You can find additional information on the following topics in the S7-1500T Motion Control function manuals:

Measuring input type: Timer DI

Measuring input type: SINAMICS (central measuring input)

Measuring input type: PROFIdrive ** (drive or external encoder)

Lost Edge Counter (LEC)


上海騰希電氣技術有限公司專注于西門子PLC,V90伺服,V20變頻器等, 歡迎致電 13681875601

• 詞條

  詞條說明

• 系統時間DST 概述 (S615)

  DST 概述 (S615)夏令時切換在此頁面中，可以創建新的夏令時切換條目。該表提供現有條目的概述。說明DST 編號 (DST No.)顯示條目編號。如果創建新的條目，會創建一個帶有一編號的新行。名稱 (Name)顯示條目名稱。年 (Year)顯示條目的創建年份。起始日期 (Start Date)顯示夏令時的起始月、日和時間。結束日期 (End Date)顯示夏令時的結束月、日和時間。重復日期輸

• 組態系統功能 設備

  設備該頁面包含常規設備信息。說明該頁面包含以下框：當前系統時間 (Current System Time)（僅在線時可用）顯示當前系統時間。系統時間由用戶或時鐘幀設置：即 SINEC H1 時鐘幀、NTP 或 SNTP。（只讀）系統運行時間 (System Up Time)（僅在線時可用）顯示設備自上次重啟以來的運行時間。（只讀）設備類型 (Device Type)（僅在線時可用）顯示設備的型號標

• 項目文本基本知識

  項目文本基本知識項目中不同語言的文本在處理項目的過程中輸入文本時，通常會使用用戶自己的語言進行輸入。 如果之后將該項目傳遞給某個不懂該語言的人員，他需要將把相關的文本翻譯為他們自己可理解的語言。 這也就是所有文本都可翻譯的原因。 這樣，可以確保以后遇到這些文本的任何人都能以其選擇的語言來查看文本。項目語言項目語言是以后使用項目時所采用的所有語言。 基于編輯語言，所有文本都可翻譯成各種項目語言。 將

• 模擬量比例換算

  模擬量比例換算因為A/D（模/數）、D/A（數/模）轉換之間的對應關系，S7-200 SMART CPU內部用數值表示外部的模擬量信號，兩者之間有一定的數學關系。這個關系就是模擬量/數值量的換算關系。例如，使用一個0 - 20mA的模擬量信號輸入，在S7-200 SMART CPU內部，0 - 20mA對應于數值范圍0 - 27648；對于4 - 20mA的信號，對應的內部數值為5530 - 27