臨汾不錯蓄電池

時間：2018-07-06作者：北京金業順達科技有限公司瀏覽：40

臨汾不錯蓄電池


成功檢測不錯蓄電池狀態的前提是可以提供需要的交流恒流源。恒流源是能夠向負載提供恒定電流的電源裝置。它是一個電源內阻非常大的電源。為了保證內阻有較高的測量精度及較好的重現性，要求恒流電流源有足夠的穩定度，并且波形失真度要小。這里所需交流信號幅度為40mV，頻率為1KHZ

The premise of successful detection of battery state is that it can provide the needed AC constant current source. The constant current source is a power supply that can provide a constant current to the load. It is a power supply with a very large internal resistance. To ensure that the internal resistance has high measurement accuracy and good reproducibility, constant current source is required to have enough stability and waveform distortion is small. The magnitude of the AC ** required here is 40mV and the frequency is 1KHZ.
但是傳統的低頻交流信號發生器設計中存在很多的不足：應用通用電路,元器件多,尤其是電容的體積大,且波形的穩定性差、失真大,調節也較不方便；應用**電路,如ICL8038、MAX038等,其失真和穩定性方面有明顯提高,但低頻應用時不合適,調節不方便,成本也較高。
But there are many shortcomings in the traditional low frequency AC ** generator design: the application of general circuit, many components, especially the volume of the capacitance, and the poor stability and distortion of the waveform, and very inconvenient to adjust. The application of special circuit, such as ICL8038, MAX038 and so on, has obviously improved the distortion and stability, but it is used in low frequency. It is not suitable, the adjustment is inconvenient, the cost is also high.




3．1 設計原理
3.1 design principle




本文采用了數字式信號發生器產生標準正弦波和電流負反饋法產生精確交流恒流源法, 交流恒流源實現原理如圖2所示。
In this paper, a digital ** generator is used to produce a standard sine wave and a current negative feedback method to produce an accurate AC constant current source method, and the principle of AC constant current source realization is shown in Figure 2.












精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery








電路組成框圖如圖2所示：這是一個閉環控制系統，電流負反饋電路。標準正弦波產生一個頻率穩定、對稱、失真度低的1KHz正弦波信號。驅動電路把正弦波放大，去推動功放電路，得到正弦交流電流輸出。恒流控制電路從功放輸出中得到的信號，通過與給定的信號相比較，來調節驅動電路的信號，從而使輸出電流保持穩定。
The block diagram of the circuit is shown in Figure 2: This is a closed loop control system and a current negative feedback circuit. The standard sine wave produces a 1KHz sine wave with stable frequency, symmetry and low distortion. The driving circuit amplifies the sine wave to drive the power amplifier circuit, and obtains the sinusoidal AC current output. The ** obtained from the output of the power amplifier by the constant current control circuit, by comparing with the given **, adjusts the ** of the driving circuit, so that the output current is kept stable.




3．2 標準正弦波的產生原理
The principle of the generation of 3.2 standard sine wave




標準正弦波信號的產生采用數字式信號發生器。首先將正弦表數據存儲在如圖3所示的正弦信號存儲器中,晶振產生振蕩頻率f，經過整型電路變?yōu)橥暾讲l率，再經過R分頻電路得到頻率為f/R,再經過鑒相器FD和環路濾波器LF電路鎖相分頻后，讀取存儲在正弦信號存儲器中的正弦值,經過D/A轉換電路和經低通有源濾器濾波電路，生成圖2 所需的標準正弦波。
The standard sine wave ** is generated by digital ** generator. First, the sinusoidal data is stored in the sinusoidal ** memory as shown in Figure 3. The oscillator produces an oscillating frequency f, after the integral circuit is transformed into a complete square wave frequency, and then the frequency is f/R through the R frequency division circuit, and then after the phase discriminator FD and the loop filter LF circuit are locked in phase, the reading stored in the sinusoidal ** memory is read. String value, through D/A conversion circuit and low-pass active filter filter circuit, generate standard sine wave required for Figure 2.


由于電池內阻為毫歐級，因此采用常規的兩端子測量方法測量誤差較大，在此采用四端子測量方式。測量時兩個端子施加一頻率為
Because the internal resistance of the battery is millieu level, the conventional two terminal measurement method has great error, and the four terminal measurement method is adopted. At the time of measurement, two terminals are applied in a frequency








精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery




的恒定交流激勵電流信號，另兩個端子用于測量。測量工作原理圖如圖1所示，響應信號是指蓄電池注入交流恒流源后，在其兩端測出的交流電壓信號。而正弦信號是經D/A產生的作為壓控恒流源的輸入信號。
A constant AC excitation current ** and the other two terminals are used for measurement. The working principle diagram is shown in Figure 1. The response ** is the AC voltage ** measured at both ends after the battery is injected into the AC constant current source. Sinusoidal ** is generated by D/A as the input ** of voltage controlled constant current source.
























設正弦信號為：
The sine ** is set as:








精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery












（1）
(1)
蓄電池兩端的響應電壓信號為：
The response voltage **s at both ends of the battery are:








（2）
(2)








精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery
為注入蓄電池的交流電流和其兩端響應電壓信號的相位差。
The phase difference between the AC current and the voltage **s at both ends of the battery is injected.
通過模擬乘法器后有：
After the analog multiplier, there are:








精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery




K為模擬乘法器的放大系數。
K is the magnification factor of the analog multiplier.
進行低通濾波后濾掉交流成分得：
After low pass filtering, filter off the AC component:












精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery




（3）
(3)




由交流法測內阻原理得：
The principle of measuring internal resistance by AC method is obtained.








精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery




（5）
(5)
式中I為交流恒流源信號的較大值。比較（4）、（5）可得：
I is the maximum value of the AC constant current source **. Comparison (4) and (5) can be obtained:












精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery








上式中K、A、I都是已知量，而u為經過A/D采樣送到單片機進行處理的采樣值，所以在單片機中進行一個簡單的除法運算便能得到蓄電池內阻了。


The K, A and I in the upper form are all known, while u is sampled by the A/D sample to the single chip processor, so a simple division operation in the single chip can get the internal resistance of the battery.




湯淺蓄電池銷售中心：
理士蓄電池銷售中心：







北京金業順達科技有限公司專注于APCUPS電源,圣陽蓄電池,科士達UPS電源,UPS蓄電池,山特UPS電源,艾默生ups電源,松下蓄電池,理士蓄電池,湯淺蓄電池,艾默生精密空調,精密空調廠家,山特UPS電源廠家,直流屏蓄電池,模塊化機房,一體化機房等, 歡迎致電 18201588123

• 詞條

  詞條說明

• EPS蓄電池2V1000AH

  EPS蓄電池2V1000AH .理士鉛酸蓄電池短路現象及原因 理士鉛蓄電池的短路系指鉛蓄電池內部正負極群相連。鉛蓄電池短路現象主要表現在以下幾個方面： (1) 開路電壓低，閉路電壓 ( 放電 ) 很快達到終止電壓。 (2) 大電流放電時，端電壓迅速下降到零。 (3) 開路時，電解液密度很低，在低溫環境中電解液會出現結冰現象。 (4) 充電時，電壓上升很慢，始終保持低值 ( 有時降為零 ) 。 (

• 運城理士蓄電池批發價格

  運城理士蓄電池批發價格 理士蓄電池經銷商理士鉛酸蓄電池的主要特點： ?1、安全性能好：正常使用下無電解液漏出，無電池膨脹及破裂。? 2、放電性能好：放電電壓平穩，放電平臺平緩。 ?3、耐震動性好：完全充電狀態的電池完全固定，以4mm的振幅，16.7HZ的頻率震動1小時，無漏液，無電池膨脹及破裂，開路電壓正常。 ?4、耐沖擊性好：完全充電狀態的電池從20CM

• 科士達UPS**中國"較美高鐵" 一路暢行

  成貴高鐵起源于深圳已至貴陽市，從海拔高度240米的四川盆地到海拔2400米的四川盆地，追趕云、貴、川三省，被稱作“全世界**條山區地帶高鐵動車”。是在我國“八縱八橫”高速鐵路網蘭州市（西寧市）至廣州市安全通道的關鍵構成部分?？剖窟_(dá)UPS為這一條追趕云、貴、川三省的主要安全通道確保能源供應成貴高鐵全線貫通后將完畢沿路隆昌宜賓市、滇北昭通市、黔西畢節等地域沒有高鐵動車的歷史時間，并產生新的出川鐵路線經

• 鉛酸蓄電池短路的處理方法

  鉛酸蓄電池短路的處理方法1）減小充電電流，降低充電電壓，檢查安全閥體是否堵死。定期充電放電。UPS電源系統中的鉛酸蓄電池浮充電壓和放電電壓，很多在出廠時均已調試到額定值，而放電電流的大小是隨著負載的增大而增加的，使用中應合理調節負載，比如控制計算機等電子設備的使用臺數。一般情況下，負載不宜**過UPS額定負載的60%。在這個范圍內，蓄電池就不會出現過度放電。鉛酸蓄電池存放會因自放電而失去部分容量，因